Click here to download an installation instruction manual in pdf form
What is the main power source?
Twelve (12) volt lead acid deep draw marine battery.
Can I run six (6) volt spinning wing decoys or other six
(6) volt decoys on a twelve (12) volt system?
Yes when you turn the speed control up or down you vary the
voltage supply from 0% setting (2 volts)
to a 100% setting (12 volts). A 6 volt motor will run fine
at 12 volts, but much faster than normal.
How does it work?
Each channel will control:
- on/off
- speed - 10%-100% of any 6 volt to 12 volt motorized decoy or decoys
- on time - 0.5 seconds to 16 seconds
- off time - 0.5 seconds to 16 seconds
NOTE: Our 6 channel and 4 channel panels have a master on/off switch to control
all decoys at once, as well as individual channel switches.
How many decoys can it control?
Basically, 4 decoys per channel, of the spinning wing/duck butt category.
- 6 channel unit can control 24 decoys
- 4 channel unit can control 16 decoys
The mallard machine decoy should be connected to channel 2, which is the strongest output.
What type of motorized decoys can it control?
Any 6 volt to 12 volt DC motorized decoy device.
What is the maximum amperage ratings?
- 6 channel unit - fused protected at 30 amps, maximum operating for
entire panel: 25 amps
- 4 channel unit - fused protected at 30 amps, maximum operating for entire panel:
20 amps
NOTE: Any channel on all units can handle up to 7 amps max. Channel 2 is preferred
for decoy systems such as the Mallard Machine.
How is it installed?
Here are the steps:
1. Mount controller to anything stationary with 4 screws, bolts or nails. Wall
mounting is preferred.
2. Connect furnished battery terminals on controller to 12 volt battery power
source.
3. Run a 2-conductor low voltage cable to each device and connect other end
to terminals on controller.
What tools do I need to complete the electrical wiring to the controller?
A pocket knife or wire stripper. Pliers are not necessary.
What are the advantages of this controller?
- A single power source. No more challenges
with smaller batteries that only last a few hours
at most.
- Extended operating time. Can continuous run 6 spinning
wing decoys 3 days and nights on one fully charged 12-volt
marine battery. Controller utilizing pulse width modulation
technology.
- Realistic motion. Makes multiple decoys come alive
with more realistic motion, with different speeds and different
on-off times.
- Easy to operate. Master switch on the 4 channel and
6 channel units can immediately turn the entire motorized
spread on and off.. Each channel can be turned on and off
independently as well.
- Dependability. Built using industrial grade design
and parts for years of reliable operation. Totally encased
in epoxy for protection from the elements.
- Designed in the USA. Manufactured in the USA.
- Tested in the USA. Shipped in the USA.
What type of wire is needed to hook-up decoys?
Low voltage landscape cable available at Lowes or Home
Depot, or your local hardware store.
Recommended: 16/14 gauge for runs up to 100 feet and
12/14 gauge for runs greater than 100 feet.
Can I use different types of decoys on the same channel?
Yes, as long as any single channel total amperage does
not exceed 7 amps.
The Mallard Machine decoy system should
be connected to channel 2, which has the greatest power
ability.
Is it waterproof?
It is housed in a heavy plastic box and encased with
epoxy. All switches and variable controls have O-ring seals.
It is highly resistant to rain. However, we do not recommend
constant exposure to water.
Where is the best place to install this controller?
Mounted on a wall, sheltered from rain, within easy reach
of the decoy operator is preferred. All wiring should be
tucked back from interference with the hunter. A tie-off
bar is provided at the bottom of the controller for strain
relief of wiring connections.
My water pump decoys don't spray as high as they used to. What's wrong?
Pumps usually have a preferred direction of rotation.
Probably the electrical polarity to the pump motor is reversed.
Swapping position (polarity) of the two wires that power
the pump motor should make a difference. Also check for
trash in the pump.
|
